Gunsmithing

FRAME MOD PACKAGE: Remove finger grooves, undercut trigger guard, add thumb pads. Stipple/texture grip, thumb pads and trigger guard. 

       Fine textured stippling (similar to lava rock):  $175

        Silicon carbide/ larger stippling patterns:   $150

 

STIPPLING PER HOUR FOR CUSTOM WORK:  $50

 

SILICON CARBIDE GRIP TEXTURE: complete coverage of grip with non-slip silicon particles. Like sandpaper, great for competition and carry guns! Permanent alteration of grip, this is not a removable sticker type grip.

         Without removal of finger grooves:  $55

         With removal of finger grooves:  $75

     

THUMB PAD INDEX POINTS: Add beveled thumb index points on front end of frame on both sides with stippling:  $45

UNDERCUT TRIGGERGUARD: Cut for higher grip on pistol. Includes stippling underside of trigger guard:  $45

GRIP CHOP: Modify full length grip (G17) to compact length grip (G19):  $120 

POLISH INTERNAL PARTS: High polish all internal fire control parts:  $35

GUNSMITHING PER MAN HOUR:  $50

PER MACHINE HOUR: $75

MINIMUM CHARGE PER GUN: $35

*ALL PRICES LISTED BELOW ARE FOR LABOR ONLY AND DO NOT INCLUDE ANY REFINISHING OR PARTS*

  HANDGUN WORK

     Action Job:  $90 

    Chamfer Cylinder Chambers (.38/.357 only):  $55

    Polish Chambers (.38/.357 only):  $55

    Recrown pistol barrel:  $55

    Machine or hand cut dovetail for front sight:  $75

    Replace a missing ramp in dovetailed front sight:  $25

    Polish feed ramp:  $40

    Throat and polish pistol barrel:  $55

    Modify 1911 frame and fit beavertail grip safety:  $110

    Fit 1911 slide safety:  $45

    Fit 1911 trigger:  $75

    Fit 1911 barrel and bushing:  $125

    Fit 1911 extractor: $35

    Tighten 1911 slide:  $155

    Install staked-on 1911 front sight:  $55

    Machine front or rear cocking serrations both sides of slide:  $120

    Matte finish a stainless frame (abrasive blast):  $60 

    Polish a stainless frame:  $150-$180

    Bevel magazine well:  $80-$120

  GENERAL WORK

     Install dovetailed sights:  $40

    Test fire and site-in (handgun, shotgun or rifle):  $55 plus cost of ammo, targets and range time

    Drill and tap a hole:  $25 for first hole $15 each additional hole

    Recut checkering in wood stock:  $50/hour

    Mount and boresight rifle scope:  $50

    Installing multiple parts that do not require fitting: Hourly rate $50

 AR-15 WORK

    Installing gas block (screw on):  $35

    Install gas block (pinned): $55

    Installing muzzle device on threaded barrel:  $25

    Check headspace:  $25

    Install free float handguard:  $45

    Install aftermarket trigger:  $35

    Install or replace barrel:  $60

    Assemble lower receiver:  $50

    Assemble upper receiver:  $55

    Lap upper receiver extension:  $30-$45

AR-15 COMPLETE BUILD: Complete assembly of your parts.

 Torque all parts to factory specs, where applicable. Thread lock all screws. Fit all parts as needed for best possible function. Stake lower receiver extension tube lock nut. Lubricate and function test:  $125

SAIGA TRIGGER GUARD RELOCATION: Remove sporter stock, relocate trigger guard and rivet in place, cut hole in receiver for pistol grip and plug holes. 

         Labor Only:  $95 - $155

CLEANING, LUBRICATION AND INSPECTION

      Rifle/Shotgun:  $45-$65

      Pistol:  $35-$45

      Revolver:  $45-$55

*Excessively dirty or rusty firearms will incur the greater prices listed above
!! Email Steve@midgardarmory.com BEFORE shipping ANY firearms for repair !!

NOTE: At this time I am only capable of refinishing pistols and small parts with Norrell's moly resin or Gunkote. I can order Cerakote air-dry on request for polymer or larger parts etc. Additional costs may apply. ADD $30 to listed prices to add parkerizing before spray finishing (carbon steel only)

Pistol slide: $65

Pistol frame:  $75

Complete pistol/ revolver:  $160

AR-15 lower receiver only:  $65

AR-15 upper receiver only:  $65

Small parts only (pins, screws, etc from one firearm): $35

*For misc. non-firearm parts, please email with information for a quote.

Parkerizing is a durable, weather-resistant, non-glare, matte finish, that absorbs and retains
oils and lubricants. It is well suited for hunting, military and Law Enforcement firearms. I use zinc parkerizing which gives a charcoal-grey finish.

*Pricing includes disassembly/assembly and abrasive blasting*

       Rifle/Shotgun:  $175
       Rifle/shotgun barrel only:  $75
       Pistol/Revolver:  $125
       Pistol slide only:  $55       

Firearms with excessive pitting and damage from rust may require additional charge for refinishing. Deep pits from rust will need to be draw-filed and sanded before the part can be abrasive blasted and finally parkerized. This ensures a
professional looking final finish.

Non-firearm parts can also be parkerized as long as they are ferrous metal (No Aluminum, Brass or Stainless Steel) and will fit in the tank (max. size: 4" x 6" x38"). Email with questions and for a quote.

*Email Steve@midgardarmory.com BEFORE you ship any firearms or parts for ANY service.*